Can InfinitiStone Natural Stone be used on both exterior and interior applications?

Yes. Our natural loose stone veneers are suitable for both applications, allowing you to bring the outdoors inside as well as emphasizing your design and continuity in your colour and texture design schemes.

How are InfinitiStone Natural Loose Stone packaged?

Dependent on the item chosen, our natural Loose Stone veneers are sold in 5m2 or 15m2 crates for flats and 12lm crates for Corners. Stacked Stone are sold in boxes. Please check with us to confirm before ordering if unsure.

How are InfinitiStone products sold?

Flat pieces are sold by the square metre and external Corner pieces are per linear metre run, based on grouted finish.

Do I need to seal your natural stone?

We recommend sealing all natural stone veneers on completion of project to maintain its’ original look.
Other advantages of sealing the stone is because by nature, natural stone is porous and can better manage discolouration and the forming of lichen, algae or moss.

If subjected to prolong damp and wet weather, such as rain, which is an inevitable fact of Australia’s climate, can create an appropriate environment for lichen, algae or moss to grow. If the growth is not removed in its early stages it may darken the stone. Dark soils may also darken natural stone surfaces.

Should I colour the mortar/grout?

Dependent on the finish you seek, where applicable, the colour of your grout can enhance the look of your stone wall.

Can InfinitiStone Natural Stone be used on wall areas adjacent to swimming pools?

InfinitiStone natural loose stone veneer products will perform the same as any other natural stone veneers. It should be taken into consideration with any natural material that continued exposure to chlorine and other chemicals may eventually affect the coloration of the products. When frequently exposed to water, we recommend protection with a compatible natural stone sealer.

What substructure do you recommend to clad InfinitiStone Natural Loose Stone Veneers?

InfinitiStone natural loose stone veneers may be adhered to pre-prepared brick, block or concrete wall substructures. See our General Install Guide for more details.

Can InfinitiStone Natural Stone Products be cut?
Yes. InfinitiStone natural stone can be cut or trimmed using a wet tile saw. You may also use a hand held grinder with diamond blade or chipper with hammer to chip to form smaller infill pieces.

 

What is the average thickness of InfinitiStone Natural Loose Stone Veneers?

Average thickness on our natural stone veneers range from 10-50 millimetres dependent on range.

How heavy are InfinitiStone Natural Loose Stone Veneers?

Our natural stone ranges from 35 – 75kg/m2 in weight dependent on selection.

What are Limestone, Granite, Quartzite and Slate Stone?

Limestone is the most common Sedimentary rocks found and are formed primarily from remains of plants, animal remains and reefs through thousands of years. Limestone comes in different colours and textures.

Granite is an igneous rock and one of the hardest and toughest natural stones, comprising of quartz and feldspar, it is granular and phaneritic in texture.

Quartzite is a metamorphic rock, comprising of a high quartz composition therefore are a far harder stone than slate or sandstone.

Slate is a fine-grained, homogeneous metamorphic rock and features one of the most naturally slip-resistant surfaces of most natural stone.

Are your loose stone all natural or reconstituted?

Our loose stone veneers are natural quarried stone, not reconstituted or manufactured.

How do I order?

Simply email us your Invitation to Quote, stating your required product code and quantity required, including advising your contact details & project address, including postcode and one of our experienced staff will be in contact with you to discuss and/or submit best price proposals.

Limitations of Photographic Process

Colour variations are evident in all manufactured and natural stone products and whilst the colours reproduced in this website and/or on our brochures are as accurate as photographic processes allow, it is essential that your choice is made from actual samples reviewed.

Manufactured Product Colour Variations

Colours form an integral part of InfinitiStone products during the casting process as such it is colourfast. Existing applications show no undesirable colour change after years of various weather conditions. We do recommend applying a suitable sealer for better surface protection.

How many product types are available?

There is a wide variety of products in several different colour tones to choose from. Browse through our site for more information.

Can we seal the stone?

Our manufactured and natural stone range are porous by nature and so we recommend sealing the stone. In choosing a sealer, use a penetrating, breathable sealer which will keep its original tone or use a satin sealer for a sheen finish. Note: A sealer may affect the stone colour and create a sheen, so always test a small area beforehand.

Can InfinitiStone Manufactured Stone Cladding products be used on both exterior and interior applications?

Yes! InfinitiStone products are suitable for both applications, allowing you to bring the outdoors inside as well as emphasizing your design and continuity in your colour and texture design schemes.

Our manufactured stone selection are non-combustible and meets AS3837 – 1998 standards, rated as a group 1 or better material.

How are InfinitiStone products packaged?

Dependent on the item chosen, most manufactured and natural stacked stone selection come in boxes containing varying m2 and lineal metre corners. Check in with us for confirmation. Our natural loose split stone are sold in 5m2 or 15m2/Crate flats and 12Lm/Crate Corners. 

 

How are InfinitiStone products sold?

Flat pieces are sold by the square metre, where available, external Corner pieces are per linear metre run. 

How do I install Infiniti Stone products?

Use mortar or premixed adhesives. Please refer to our install guide.

Will InfinitiStone manufactured Products fade?

Colours form an integral part of InfinitiStone products during the casting process as such it is colourfast. Existing applications show no undesirable colour change after years of various weather conditions. We do recommend applying a suitable sealer for better protection and performance.

Does InfinitiStone manufactured Products shrink?

InfinitiStone manufactured ranges do not shrink once installed. As with all molded products, there may be minor shrinkage during curing time in the factory. Tolerance is + or – 3-5mm.

Should I colour the mortar/grout?

Dependent on the finish you seek, where applicable, the colour of your grout can enhance the look of your stone wall. Our natural and manufactured Stacked Stone selection do not require grouting.

Can InfinitiStone Manufactured Stone products be used on wall areas adjacent to swimming pools?

InfinitiStone products will perform the same as any other high quality masonry material. It should be taken into consideration with any masonry or natural material that continued exposure to chlorine and other chemicals may eventually affect the coloration of the products. When frequently exposed to water, we recommend protection with suitable sealers for better performance.

Our natural Stacked Stone should be sealed using a suitable natural stone sealer.

Can InfinitiStone Manufactured Stone products be used on walk-ways or patios?

All our manufactured selection are designed for wall cladding only.

What type of sub-surface is suitable to clad InfinitiStone Manufactured Stone?

InfinitiStone products may be adhered to practically any prepared, clean, untreated, structurally sound wall surfaces. This includes Concrete/Cementituous Board or masonry walls. Please refer to substrate manufacturer’s instruction for appropriate preparation work to receive InfinitiStone veneer.

Can InfinitiStone Manufactured Stone Products be cut?

Yes! InfinitStone manufactured products can be easily cut or trimmed using a hand held grinder with a diamond blade. You may use a wide-mouth nipper for edging if desired.

We recommend cutting our natural stone ranges with a wet saw with diamond blade.

What is the average thickness of Manufactured InfinitiStone?

Average thickness on our manufactured ranges are 20-60 millimetres dependent on range.

How heavy are InfinitiStone Manufactured Stone products?

The weight varies by selection. The approximate weight on our manufactured ranges are 30-45 kilograms per square metre dependent on the product selected.

Our natural stacked & split loose stone ranges from 35-75 kg/m2.

What are InfinitiStone manufactured ranges made of?

Our manufactured stone are hand crafted from many different pieces of natural stone molds, with its colour and texture created using a unique blend of cement, lightweight aggregates and iron oxide pigments.

Does the colour go all the way through your manufactured stone ranges?

Yes! A base colour is blended throughout the entire product. Colour overtones are applied and integrated into the product during the casting process. Please note that as every stone is handmade, colours may vary slightly from samples.

Is our Light Weight Stone Veneer real stone?

InfinitiStone manufactured (handmade) stone products have distinctive advantages over real stone, as follows;

· It is light weight (as much as 30-50% less than real stone),
· It can be cladded onto practically any new or existing structurally sound wall , mostly without additional structural support,
· It is colourfast,
· It is durable and is non-combustible, meets AS3837 – 1998 standards – rated a group 1 or better material
· It is easy to install – as much as half your installation time saved!

We also have a range of natural stacked stone which are factory cut and adhered together manually and are typically 200mm High x 400mm Long Z profiles or 150mm High x 600mm Long panels or 200mmH x 600mm Long Z-panels.

Please see our Products Page for full range and details.